[Table of Contents] [Search]


[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Vandercook Parts, rollers, for sale.



Vandercook parts for sale.

I bought the remnants of a shop a few weeks ago, and amongst the items I do=20
not need are some parts, listed below, for Vandercook proof presses. Mostly=20
for Universal #1=92s,  as they had three of these. I am trying to get these=20
parts into hands that can use them.=20

The =93fat core=94 rollers and their shafts have been separated as different=20
parts because various presses  use the same cores on different length shafts=
.=20
If you are interested in spare rollers, measure your form rollers and shafts=20
carefuly to see if the listed parts will work for you.

For Sale -=20
Item #1 - Beautiful original Vandercook  .968=94 chromed roller height setti=
ng=20
gage.

Item #2 - Solid brass paper side guide assembly, complete, micro adjustable.
(part number L-3 ??)

Item #3 - Form roller gear, 48 teeth, 3 and 1/8=94 diameter,   5/8=94 center=20
hole, for the shafts of =93fat core=94 form rollers.

Item #4 - Form roller gear, 48 teeth, 3 and 1/8=94 diameter,  1/2=94 center =
hole.=20
 ( NOT for a Universal 1 press - so far as I know)

Items #5 (a-b-c-d) - Four retaining slotted cap screws (part number X-14099)=20
- to hold cores to bearing  blocks,  1 and 11/16=94 long with a  3/8=94 x 24=20
thread,  a  land of .470=94 for bearing, set screw in center locks screw int=
o=20
the core.

Items #6 (a-b-c-d) - 4 bearing block assemblies with bearings (complete with=20
adjusting knobs)  - two left side, two right side. (left hand side =3D part=20
number X-16836 ? ) (right  hand side =3DX-1683 ? )( 1990 new price =3D $128.=
90=20
ea.) They currently contain good Federal #1201FF bearings, but replacement=20
bearings are still made and easy to find if needed.

Item #7 - One 3/4=94 diameter by 20 and 11/16=94 small core form roller, wit=
h=20
original Vandercook roller that has shrunk to 2.85=94 diameter, too small to=20
adjust or use, good as a core only I think. Uses item #5 retaining  screws i=
n=20
ends.

Item #8 - One 3/4=94 diameter by 20 and 11/16=94 small core form roller, wit=
h=20
original Vandercook roller that has shrunk to 2.85=94 diameter, too small to=20
adjust or use, good as a core only I think. Uses item #5 retaining  screws i=
n=20
ends.

Items #9 (a-b-c) - Three bare roller cores for the small core form rollers,=20
3/4=94 by 20 and 11/16=94 - all can use item #5 retaining  screws in ends.

Items #10(a-b-c)  - Three  =93fat core=94 form rollers,  19 and 5/8=94  by  =
1 and=20
5/16=94 core, (part number X-14616 ?) used with the 5/8=94 (part number  X-1=
4095=20
?)  shafts in the center. All good as cores only.=20

Items #11 (a-b) - Shafts  (part number X-14095 ?) for fat core rollers form,=20
a ground 5/8=94, by 20 and  11/16=94 shaft.  Can use item #5 retaining  scre=
ws in=20
ends.

Item #12 - Shaft for fat core rollers form. a ground 5/8=94, by 21 3/8=94 sh=
aft=20
with bearing lands of .471=94 diameter ground onto ends, does not use the it=
em=20
#5 retaining screws, but something smaller.

Item #13 - Vandercook manual for  Universal #1 hand press, has parts diagram=
s.

Any or all parts are for sale for the best offers I get over the next two=20
weeks or so. Shipping cost is additional to sale price.  Things will be a bi=
t=20
uncertain until I determine if anyone wants enough parts for a full set of=20
spare rollers. Preference will be given to anybody who needs  cores, bearing=20
blocks, retaining screws, etc., for a whole spare set of rollers, or if they=20
have a press and no rollers at all. If nobody wants a set, I will parcel out=20
single parts separately. I suggest that I cut away the rubber from the cores=20
to save shipping weight, because the cores are 2.5 pounds, the cores with=20
rollers are about 7 or 8  pounds each.

If interested in something, or if you have any questions, let me know by=20
e-mail.=20

Bill Simon
BSimon1234@aol.com
Phoenix.


[Subject index] [Index for current month] [Table of Contents] [Search]